As your computer configuration becomes more complicated and/or sophisticated, sometimes the system becomes difficult to configure and run properly. This problem is often caused by IRQ Conflicts. IRQs (Interrupt ReQuest) are unique signals that allow the cards or components to communicate with the system. Many current accessory cards still require an IRQ dedicated to their specific use. About fifteen years ago, when the architecture for the IBM PC-AT with the 16-bit bus was first defined, it was thought that a total of 15 useable IRQs would be sufficient for a system's needs. It is doubtful that anyone back then expected these systems to grow to the complexity that they have reached. (For a more complete understanding of the IRQs and what it means, read the "What is an IRQ?" explanation near the end of this section.)
In most cases, the difficulties in configuring your system can be avoided by using current cards (PCI) that allow IRQ sharing. The proper card installation sequence can also help. Changing the installation sequence often helps because many of these cards can use only one of a predefined selection of IRQ values (specific to each card). By using the proper sequence, the system can often install the cards in such a way as to keep the proper IRQ available for the next card, thereby eliminating IRQ conflicts that occur when two boards try to use one IRQ.
Here is the sequence that our testing lab has found that works for the system configuration examples listed below (this sequence is very dependent on board/BIOS version).
Installation Sequence for 3rd Party Manufacturers' Components:
For BCM and Microstar motherboards utilizing
Award BIOS W6167MS v1.1b9 082299 5:0052
Installation Sequence for:
| One (1) AGP slot
|| One (1) AGP slot|
| Six (6) usable card slots, consisting of:
|| Six (6) usable card slots, consisting of:|
| Five (5) PCI slots, (one shared)
|| Four (4) PCI slots, (one shared)|
PnP Operating System is "ENABLED" for Windows® 95 and Windows 98
PnP Operating System is "DISABLED" for Windows NT®
The operating system (Windows 95/98 or Windows NT) should be loaded with the graphics card installed on the motherboard. (AMD recommends using an AGP graphics card). Configuring your system with only the graphics card (normally AGP, but could be PCI), RAM, and the storage drives (FD, HD, ATAPI CD-ROM or DVD, will allow you the easiest startup with a lower possibility of system conflicts. (If you are using SCSI drives, the PCI SCSI card must be installed also.)
Note: If multiple non-essential cards (devices) are included in the initial load of the operating system in addition to the graphics card, the possibility of system conflicts are more likely.
After the basic system has been configured (and after you have successfully loaded your operating system) you should add each additional component one at a time in the order listed below. This will require that you properly install each card, configure the BIOS, and restart your computer each time you install a new card.
After the installation of each component into your computer, it is advised that you note the IRQ setting on the splash screen (this is the screen that shows up momentarily when you start your system). To freeze this screen so you can easily read it, press the Pause Break key (located at the top of your keyboard) as soon as you see the screen that lists IRQ usage. Note: it may take you more than one try to press the button at just the right moment. Or, you can inspect the IRQ settings found in your Windows 95/98 Control Panel under System, then Device Manager. Always record the IRQ settings and the devices to which they are assigned each time you install a new device or component that requires an IRQ address. This information can be utilized to help resolve a system conflict or crash as the result of an IRQ conflict.
After each successful installation of a component from this list, you will need to exit and shut down your system and unplug it before installing the next component.
Note: in case you are not planning to use one of the devices listed below, just skip to the next device in the sequence of installation. Generally, ISA based components are less flexible; therefore, if you must use any ISA based components, you may decide to install these first. The sequence below is only a suggested guideline to follow.
Loading Sequence for Additional cards:
Internal Modem (PCI)
Sound Card (PCI or ISA)
Network Card, a.k.a. NIC (PCI or ISA)
DVD Devices requiring Dxr3 Decoder Board (PCI)
Note: Some video decoder boards require two (2) IRQs for complete functionality. Check with your video decoder card manufacturer for video decoder support and requirements.
SCSI Adapter (PCI) (This assumes that the system does not have a SCSI hard drive.)
External Modem: May be installed anytime after the operating system has been successfully installed. This includes regular v.90 modems as well as ISDN modems.
Diamond Monster 3D Voodoo I or Voodoo II Cards: Since these cards do not require an IRQ address, it is recommended that they be installed after the successful installation of your operating system. They do require a PCI slot.
Other 3rd Party Manufacturer Component Cards: Many other 3rd party manufacturer component cards may require an IRQ. Be sure to check with the manufacturer of your product to find out the exact installation requirements before you attempt to install it into your computer system. It is recommended that these component cards be installed after all of your other primary cards are installed if you have unused IRQ addresses available.
As you install the next device into your computer, you may experience a system conflict. You may be required to change the sequence of installation of the components being installed into your particular computer (i.e. which comes first, second, third, etc.).
IRQ Conflicts During Installation and Configuration:
It would be ideal to be able to have a system with an unlimited number of slots and IRQ addresses. Unfortunately, the way PC systems were designed many years ago causes limitations today.
When the basic design concepts of the PC architecture were defined, there was a specific number of slots allowed and a limited number of IRQs. With the limited number of IRQs available in today's systems, if you are using old-style cards that do not allow IRQ sharing, you may not be able to install all of the devices you that you desire using PCI-based components without experiencing a system conflict. You may consider using ISA-based components as well as an external modem to optimize the utilization of assigned IRQs for cards or components that require a dedicated IRQ.
You should carefully investigate and choose the types of devices that require a dedicated IRQ for your system. The more devices you want to install, the harder it will be to find an available IRQ that the device can use, or is capable of using. This becomes even more of a challenge for devices that require two IRQ addresses (specific sound cards, DVD devices, etc.).
Although the procedure listed above has worked in a testing lab environment, you may need to perform some experimenting to determine the best sequence and method of setting up your devices to for proper computer operation. Check the manufacturer's literature for each component used and list the IRQs with which each is compatible. List all of the IRQs and determine the path that allows the devices to use available IRQs. To install all of the devices you wish to use, you may have to exchange one of your devices for another type (i.e. change from a PCI sound card to an ISA sound card or vise versa) for proper configuration. Check with the manufacturer to determine if there is an upgraded version of the card. Sometimes a newer version or a different brand of the component may solve the problem. Systems cannot properly function if the number of cards and/or devices installed require more IRQs than are actually available within the computer.
What is an IRQ?
The easiest way to explain an IRQ is to think of it as an unique identifier. The IRQ process is similar to an auction. The CPU is the auctioneer and the peripherals are the bidders. Each bidder has a flag or paddle to get the auctioneer's attention. If more than one bidder has the same flag, there is chaos. Almost all primary components, such as graphics, sound, modem, etc., require at least one IRQ, regardless of whether they are cards or built onto the system boards. Many older devices require their own unique IRQ (their unique flag) with respect to all of the other devices. Newer cards can often share IRQs, but older cards usually cannot share with each other because they treat their IRQ as their own. When two of these older devices try to use the same IRQ, one or more of the devices will not function properly. This is called an IRQ conflict. Such conflicts can cause improper performance, system lock-ups and crashes.
Most newer components, however, can share an IRQ. Sharing an IRQ is the modern way to allow more cards to be added to a system. Note that some components (like video cards) cannot share IRQs. This is because the video card's IRQ is usually 10, 11, or 12. These are low priority and may get delayed (or lost) due to higher priority requests. This can cause undesirable visual effects. Cards that fully conform to the intent of the PCI Plug-n-Play standard allow IRQ sharing.
There are 16 IRQs (15 usable) in a computer system. Here is a typical assignment of these IRQs:
IRQ 0 System- System Timer
IRQ 1 System- Keyboard
IRQ 2 System- Cascadeable PIC (programmable interrupt controller), controls IRQ 8-15
IRQ 3 System- Serial Port (COM 2 and COM4)
IRQ 4 System - Serial Port (COM 1 and COM3)
IRQ 5 Available- General Adapter Use
IRQ 6 System- Diskette Controller
IRQ 7 System- Printer 1
IRQ 8 System- CMOS Real-time clock
IRQ 9 Available- General Adapter Use
IRQ 10 Available- General Adapter Use
IRQ 11 Available- General Adapter Use
IRQ 12 System- Mouse Port
IRQ 13 System- Math Co-processor (even though this is built into the CPU, it still uses an IRQ)
IRQ 14 System- Hard Disk Controller
IRQ 15 Available- General Adapter Use
As you can see, there are five (5) IRQs that are not assigned by the system design. Of these, one usually goes to the graphics card, one to the USB ports, and one to the modem. That leaves two (2) available IRQs for everything else. With care (and use of the proper cards), this is normally sufficient.
AMD makes no representations or warranties with respect to any information provided on this web document relating to the products of other companies, and expressly disclaims any implied warranties of merchantability, fitness for a particular purpose, non-infringement or warranties from course of dealing or custom of trade with respect to such information. Furthermore, the inclusion of such information does not constitute an endorsement or certification by AMD of the product.
Please visit the System Build & Installation Page for available documents that will guide you with the configuration of a stable AMD Athlon MP platform.